Select Page
Eyedro EYEFI-2 Unboxing

Eyedro EYEFI-2 Unboxing

Eyedro EYEFI-2 Unboxing Video

Energy Monitoring Made Easy

Eyedro EYEFI-2 unboxing – a short video overview of the components of the solar-ready, WiFi connected EYEFI-2 home energy monitor.

What’s in the box?

  • 1 x sensor module
  • 2 x 200 amp rated split core current sensing transformers
  • 1 x 120V AC – 6V AC North American Type A power adapter
  • 1 x EYEFI Quick Start Guide
Eyedro EYEFI-2 Components

Shop Now

Shop for Eyedro EYEFI-2

Eyedro Home Feature Comparison

Eyedro Home Feature Comparison

Select the Eyedro Home Electricity Monitoring System that has the features that matter most to you!

All Eyedro residential LV series and EYEFI products are compatible with ESCLV series current sensors from 5A – 200A.

Shop Eyedro Home!

Eyedro home feature comparison chart
Eyedro Home Electricity Monitors – Feature Comparison

All Eyedro residential LV series and EYEFI products are compatible with ESCLV series current sensors from 5A – 200A.

Shop Eyedro Home!

Eyedro Installation: Opening the Panel and Installing the Eyedro Sensors

Eyedro Installation: Opening the Panel and Installing the Eyedro Sensors

Eyedro Installation: Opening the Panel and Installing the Current Sensors

While we always recommend that you hire a licensed electrician to install your Eyedro sensors, many home owners opt to install their Eyedro system themselves.  Always shut down the power to your electrical panel first and proceed with utmost caution!

Once the power is shut off at your electrical panel you can remove the cover to expose the circuits.  Your Eyedro sensors can be clamped over any individual branch circuits that you would like to monitor, but most homeowners choose to clamp the sensors over the 2 main lines that feed their panel (and usually their entire home).

For more information and a video demonstration of this step: Eyedro Installation: Opening the Panel and Installing the Current Sensors

Once you choose the circuits that you want to monitor you will need to close the sensors.  To ensure accurate measurements the sensors must be shut securely.  Eyedro current sensors will almost always make an audible clicking sound when you snap them shut.  To close the sensor, gently push down and on an angle from the hinge until you hear the click.

Routing the Eyedro Current Sensor Cables Through a Panel Knockout

You will want to route the Eyedro sensor cables out through a knockout in your electrical panel.  Please install a bushing in the knockout to protect the wires from sharp metal edges:

electrical panel knock-out bushing

Electrical Panel Knock-out Bushing

Connect your sensor wires to the sensor ports on your Eyedro.

That’s it!  Now you are ready for the next step:

Connecting the Eyedro Gateway and Cables

How to Install Eyedro Sensors

How to Install Eyedro Sensors

How to Install Eyedro Sensors

How to install Eyedro sensors is a common question.  Installation of the Eyedro electricity monitor is quite simple, and it starts with the sensors.  Although we always recommend an electrician install the sensors, it is quite common for a home owner to install their own.  The typical residential installation of the sensors inside the electrical panel looks like this:

 

Electrical panel with eyedro sensors installed.

Electrical Panel with Eyedro Sensors Installed

 

Take Extreme Caution if you do this sensor installation yourself because the electrical lines will probably be energized and pose a safety risk!  If you’re not sure what I mean then please have an electrician install these sensors for you.

Notice how there is a sensor around both of the “hot” lines entering the panel, but not the ground or neutral line. The sensors are not directional, meaning Eyedro can be used to monitor power generation just as easily as power consumption. They’re also hinged to simplify installation.

 

Eyedro Sensor - Shown Open

Eyedro Sensor – Shown Open

Also, be sure to confirm the rating on the sensors you’re installing are sufficient for your application.  At the time of this writing, Eyedro only sells a 200A sensor (red and black).

Simply clamp the eyedro sensors around the “hot” wires that are to be monitored, and ensure the sensor “snaps” closed.  Next step is to route the sensor wires through the side of the electrical panel and out to Eyedro sensor module (black box).  Here is a video by Jamie Boyd at Boyd Electrical that should also help.

 

 

For additional information regarding installation of the eyedro sensors, please consult the eyedro product manual.